HOW TO USE

Before using your e-cigarette for the first time, please read through the instruction manual that came with your unit to familiarize yourself with your specific model.

The following information is a general guide, if your model's instructions differ, please follow them instead.

Charging Your Battery

(Your batteries come pre-charged from the factory, but they should be topped off before first use.)

AC Charger

• Plug the power cord into the charger.
• Plug the power cord into a wall outlet, and the power LED will turn green.
• Gently screw the battery unit into the charger until snug - DO NOT OVER TIGHTEN. The charger's LED will turn red, indicating the battery is charging.
• The charger's LED will turn to green when the battery is completely charged. Your battery is now ready for use.

USB Charger

• Plug the USB charger into a USB port or AC adapter, and the charger's LED will turn to green.
• Gently screw the battery unit into the charger until snug - DO NOT OVER TIGHTEN. The charger's LED will turn red, indicating the battery is charging.
• The charger's LED will turn to green when the battery is completely charged. Your battery is now ready for use.

Preparing The Atomizer For First Use

The atomizer is shipped from the factory with the wick saturated in a conditioning and storage fluid. Although the fluid is perfectly safe to "vape", it has a terrible taste, and it is recommended that you clean the atomizer prior to use.

"Quick Clean" Method

• Blow through the atomizer from the threaded end into a cloth or paper towel until no more fluid comes out.
• *Drip 2 or 3 drops of your favorite e-liquid into the atomizer (cartridge end) and let it soak in for 5 minutes or so. *If you will be using pre-filled cartridges, attach the cartridge to the atomizer and let sit for at least 15 minutes to allow the wick to become saturated.

"Complete Clean" Method

• Soak the atomizer assembly in a pure grain alcohol (like Everclear) or isopropyl alcohol (rubbing alcohol) for several hours.
• Thoroughly but gently rinse the atomizer in distilled or purified water.
• Stand the atomizer on end (threaded side up), on a dry cloth or paper towel, and let air dry for 24 hours.
• *Drip 2 or 3 drops of your favorite e-liquid into the atomizer (cartridge end) and let it soak in for 5 minutes or so. *If you will be using pre-filled cartridges, attach the cartridge to the atomizer and let sit for at least 15 minutes to allow the wick to become saturated.

Assembling Your E-Cigarette

• Gently screw the atomizer onto the battery until snug - DO NOT OVER TIGHTEN.
• Attach the cartridge by firmly pushing it straight onto the atomizer. DO NOT TWIST THE CARTRIDGE WHILE ATTACHED TO THE ATOMIZER - IT CAN PERMANENTLY DAMAGE THE ATOMIZER.

Your e-cigarette is now fully assembled and ready for use.

Using Your E-Cigarette

The key to a quality vaping experience is to take smooth, consistent drags from your e-cigarette. The length of time and how hard you draw affects the taste and quantity of the vapor. This is where you will have to experiment and see what works best for you.

The main thing to keep in mind is to not overheat the atomizer through quick and repeated use. This can cause damage to the atomizer. If you notice a burnt or metallic taste, or the atomizer is getting hot to the touch, give a little more time between drags and check your cartridge for dryness.

Filling And Refilling Cartridges

Filling a new (dry) cartridge

• Remove the cartridge from its packaging.
• Insert a thin pin, like a sewing needle, safety pin or paper clip in between the cartridge filler and the cartridge wall.
• Drip the e-liquid down the pin to fill the cartridge from the bottom up.
• Squish the filler material with the pin to remove any excess air, then top off the cartridge so the filler looks saturated but not overflowing. A new cartridge should take between 10 to 20 drops of e-liquid to fill completely, depending on cartridge model and filler material.

Refilling a used cartridge

• Remove the cartridge from the atomizer.

You should be able to to just drip a couple of drops of e-liquid onto the cartridge filler to refill, but if you find that the cartridge is not soaking up the e-liquid, please do the following -

• Insert a thin pin, like a sewing needle, safety pin or paper clip in between the cartridge filler and the cartridge wall.
• Drip the e-liquid down the pin to fill the cartridge from the bottom up.
• Squish the filler material with the pin to remove any excess air, then top off the cartridge so the filler looks saturated but not overflowing. 

E-Cigarette Cleaning And Maintenance

It Is recommended that you periodically clean your e-cigarette to maximize its life and performance.